qmk_firmware/keyboards/handwired/tractyl_manuform/5x6_right/f411
2022-03-06 22:12:17 -08:00
..
chconf.h [Keymap] Drashna's Improve OLEDs and custom Split code (#14063) 2021-08-21 13:34:44 -07:00
config.h [Keyboard] Overhaul Tractyl Manuform (#16134) 2022-01-30 13:29:43 -08:00
f411.c [Keymap] Unicode and Pointing Device and Autocorect for drashna keymaps (#15415) 2021-12-14 20:53:36 -08:00
f411.h [Keymap] Drashna's Improve OLEDs and custom Split code (#14063) 2021-08-21 13:34:44 -07:00
halconf.h [Keyboard] Updates for Tractyl Manuform config (#14641) 2021-09-29 09:30:25 -07:00
mcuconf.h [Keymap] Drashna Mouse keys and oled updates (#16556) 2022-03-06 22:12:17 -08:00
post_config.h [Keymap] Drashna's OLED rewrite (#15981) 2022-01-21 19:36:52 -08:00
readme.md [Keymap] Unicode and Pointing Device and Autocorect for drashna keymaps (#15415) 2021-12-14 20:53:36 -08:00
rules.mk [Keymap] Unicode and cursor sync - drashna keymap (#15328) 2021-11-28 23:41:59 -08:00

Drashna's Blackpill Tractyl Manuform (5x6) with a right side trackball

  • System Timer on TIM5
  • VBUS mod, using PB10 -- does work, but not on my tractyl... bad soldering probably
  • Split Hand Pin, using PC14
  • Full Duplex Serial/USART using PA2 and PA3 on USART2
  • PWM Audio using PB1 and TIM3 and GPT on TIM4
  • PWM WS2812 RGB using PA1 TIM2
  • 8KB SPI EEPROM chip sharing PA5-PA7 on SPI1 with PA4 as CS pin
  • pmw3360 sensor sharing PA5-PA7 on SPI1, with B0 as CS pin
  • Encoder using PA13 and PA14
  • SSD1306 OLED display (128x64) using PB8-PB9 on I2C1
  • Pull-up resistor (22k) on PA10 to fix reset issue.
  • Pull-up resistor (5.1k) on PA1 for WS2812 LED support, and wire it's VCC to the 5V pin.
  • Pins PA9 is meant for VBUS sense, and has an internal pulldown resistor. A 5.1k pullup resistor can work (but should be avoided)
  • Pins PA11 and A12 are not useable because they're used for USB connection, and can't be shared.
  • Pin PB2 is used by BOOT1, and is unusable

Keyboard Info

Make example for this keyboard (after setting up your build environment):

make handwired/tractyl_manuform/5x6_right/f411:default

Flashing example for this keyboard:

make handwired/tractyl_manuform/5x6_right/f411:default:flash

See the build environment setup and the make instructions for more information. Brand new to QMK? Start with our Complete Newbs Guide.

Bootloader

  • Bootmagic reset: Hold down the top right key on the right side, or the top left key on the left side while plugging in.
  • Physical reset button: Briefly press the "USER" button on the BlackPill
  • Keycode in layout: Press the key mapped to RESET.