qmk_firmware/keyboards/standaside/rules.mk
FateEverywhere e88a75904b [Keyboard] Add Stand Aside keyboard (#5360)
* 412_64 move to handwired

412_64 and its second printing, Mark Zero Stand Aside, are now obsolesced by new hardware. As only two units exist in the wild not owned by me, I'm moving the definition to handwired.

* Mark 3 Stand Aside ready for production.

Uploading firmware, compiled and tested, for Mark 3 Stand Aside. The hardware's ready, now the software is too.

* Whoops.

Should've branched before pushing Stand Aside. Sorry 'bout that.

* Revert "Whoops."

This reverts commit d222046cfe.

* Revert "Mark 3 Stand Aside ready for production."

This reverts commit c790899af7.

* Mark 3 Stand Aside ready.

Initial commit for Mark 3 Stand Aside, ready for production.

* Update keyboards/standaside/rules.mk

noroadsleft suggested removal of a line, 'LAYOUTS = ortho_4x16'. I agree.

Co-Authored-By: FateEverywhere <41215461+FateEverywhere@users.noreply.github.com>

* Cleanup for pull request.

Making changes requested by Drashna, as they're all good, and I know way less about the standards than they do.

* Initial cleanup completion.

Missed a few lines in standaside.c, they're cleaned up now.
2019-03-11 13:49:23 -07:00

73 lines
3.2 KiB
Makefile

# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = atmel_dfu
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
RGBLIGHT_ENABLE = yes # Enable RGB underlighting support